Several factors help prevent lifts from tipping over. These factors include safety, center of gravity, electrical wires, and frame cradle pads. To make sure that your car lift does not tip over, take a few minutes to check it out. If you notice any problems, contact the manufacturer or ask the customer service center for help.
this handy scissor car lifts article
When using a car lift, the safety of the vehicle and the people inside it are of paramount importance. People occupying the vehicle will change the center of gravity of the vehicle, making it prone to tipping over. This can result in a fall from the lift. To prevent this accident, lifts must be equipped with safety features.
A lift’s safety is also compromised when it is improperly balanced. The center of gravity of the vehicle should be within the support area of the lift. Otherwise, the vehicle will tip or slide off of it. It should be noted that swing arm restraints do not work properly if the vehicle is not centered correctly. Therefore, it is necessary to remove any objects, such as jack stands, that may interfere with the center of gravity.
Center of gravity
When you’re lifting a vehicle, you need to make sure that it’s properly balanced and centered on the lift. This requires a center of gravity that’s located within the vehicle’s center of gravity support area. If it’s not, it can tip or slide off the lift. It’s also important to note that swing arm restraints are not meant to keep a vehicle from sliding off. This means that you should always remove any objects in the vehicle that could potentially affect the center of gravity.
To determine the proper location of your steering column, look at the center of gravity of the car. It is usually below the driver’s seat on rear-wheel drive cars and slightly in front of the steering wheel on front-wheel drive cars. In addition, a car’s center of gravity will tell you where to place the steering column for optimal alignment.
Electrical wires are necessary to prevent car lifts from tipping over. Generally, these wires are placed at certain heights. If you are working with a car lift that is over a tall building, it is wise to place them at an appropriate height. This will help you to avoid being electrocuted by electricity.
It is also wise to replace the lifting cables every three to five years or whenever damage is visible on them. While some wear and tear is normal after heavy use, it is advisable to replace them before they start to look less than brand-new. For example, if you notice that there are six random wires sticking out or more than three broken wires in one strand, it’s time to replace the entire cable.
Frame cradle pads
A frame cradle pad helps protect the lift from tipping over, and these pads come in various shapes and sizes. Some of them are made of rubber and are textured for extra grip and stability. Others are made of steel or plastic and are made to handle heavy abuse.
Whether essential Heavy Duty Car LIfts on your own working on a car or a truck, frame cradle pads can keep your car or truck from tipping over. For heavy duty vehicles, these pads are a must. They fit tightly onto the 2 post arms of BendPak lifts and straddle the vehicle’s frame. They also protect the hardware on the lift by preventing movement.
When installing a car lift, it is vital to know the proper concrete specifications. The thickness of the slab should be at least four inches and the concrete must withstand three thousand pounds of force. Depending on the brand and model, additional specifications may be required. For example, a two-post lift may only need a four-inch concrete slab, but a three-post lift with a higher weight capacity may require a thicker slab.
Once the lift is installed, it is important to pour a strong concrete floor that is large enough to support the columns. Most manufacturers recommend a minimum six to twelve-inch depth of concrete and a minimum PSI of three thousand pounds per square inch.
Checking for deformation or excessive wear on non-structural components
Regular maintenance of car lifts is critical to ensure they remain safe and functional. Lifts should be inspected by a Qualified Lift Inspector on a yearly basis to ensure they are up to the required standards. Inspectors will check structural integrity, operating mechanisms, safety systems, and any modifications. Daily inspection of lift cables is also essential to ensure that they are in good condition. If the cables have significant wear or deformation, they should be replaced.
Daily walkaround inspections should be performed to look for structural deformation or loose parts. the online blog article should be checked by a BendPak Product Specialist. Additionally, a daily walkaround inspection should include checking the lift for structural deformation or loose parts.
1419 N Midland Blvd, Nampa, ID 83651
Phone: (866) 774-7743